Skip to main content
Kofax

TAMIO Fax Error Codes

Summary

3545

Description

The table below gives you more information about the TAMIO error codes that you can find in the TCOSS trace.

Here’s an example TCOSS trace excerpt:

13/13:27:21.483 (e24/2b0) N3/T15 2.10=DisIn>TAMIO 2:Obj No.=25, Err No.=17,fkz=,VZEIT=0,ZZAHL=0

You will only find TAMIO information in the traces if you activate the “TAMIO calls” option in the TCOSS trace level. You can activate this option by adding the value 0x04 (hex) to the TCOSS tracelevel key:

HKEY_LOCAL_MACHINE\SOFTWARE\Topcall\TCOSS\TraceLevel.

For more information please check the current “TCOSS configuration manual”.

This table has been ordered according ‘Err No.=’. So if you have the choice between several ‘Error descriptions’ please also have a look at the ‘Obj No.=’.

More information about the ‘2char error’ (Two Character Error Codes) can be found in the current “TCOSS – System manual” chapter: “6.1 – Two Character Error Codes”

Transmission

Err
or
No.=

Obj
or
Nr.=

2char
or
error

Error description Reception

0

6

XB

Data error within TCI Block

Tx

0

15

XB

Data error within Form Block

Tx

1

2

X0

Call collision in Layer 7

Tx

1

16

XC

Form buffer overflow

Tx

1

25

XH

Line occupied by local telefax

Tx

1

24

X6

Reception error during routing

Rx

1 7      

2

2

X2

Error when opening back-received file

Tx

2

1

XA

Call collision in layer 6

Tx

2

25

XI

Error in selection number

Tx

3

2

X3

Error in back reception

Tx

3

25

XJ

No dial tone

Tx

4

2

X5

Error during back reception (…LOGON)

Rx

4

25

XK

Answerback mismatch

Tx

5

2

X5

Error during back reception (…ESEITE)

Rx

5

25

XL

No answer from distant telefax (fax machine)

Tx

6

25

XM

Illegal identification of called station

Tx

7

25

XN

Illegal response during training phase

Tx

8

25

XO

Three (3) learn attempts unsuccessful

Tx

9

25

XP

Illegal page confirmation

Tx

10

25

XQ

Page transmitted incorrectly

Tx

11

25

XR

Illegal frame received

Tx

12

25

XS

Unable to find appropriate baud rate

Tx

13

25

XT

No response received

Tx

14

25

XU

Busy or no dial tone on PABX connection

Tx

15

25

XV

Unexpected end of document

Rx

16

25

XW

Too many line distortions during training

Rx

17

25

XX

Illegal identification received

Rx

18

25

XY

No command received

Rx

19

25

XZ

Illegal commend received

Rx

20

25

X1

Attempt to send an empty document

Tx

21

25

XF

Ring detected

Tx

22

25

XG

Receiver not ready time-out

Tx

23

25

X9

Failed to send chained document

Tx

24

25

X8

At least one received page has not been confirmed

Rx

32

25

XA

Call collision in Layer 2

Tx

50

25

 

Dialled successfully (with dial mode only)

 

51

25

XE

Error during 2nd dial stage with DTMF

Tx

64

25

IA

Call collision

Tx

65

25

IC

No channel available

Tx

66

25

IF

No answer from distant station

Tx

67

25

II

Error in selection number

Tx

68

25

IJ

No connection to local exchange

Tx

69

25

IN

Wrong number

Tx

70

25

IS

Service of function not supported

Tx

71

25

IP

Protocol error

Tx

72

25

IU

User busy

Tx

73

25

IR

Call has been disconnected (normal call clearing)

Tx

79

25

IX

Unknown error

Tx

 

0

X?

Unexpected error code

 

Applies to

  • TC/SP – All versions (article based on TC/SP 7.84.00)

Keywords: Reception, Transmission, error message

  • Was this article helpful?